Baseline-systems FreeWave Ethernet Radio Uživatelský manuál Strana 114
- Strana / 160
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
FGR2-PE Wirelss Data Transceiver
LUM0024AB Rev A
Pin Assignment Signal Definition
7 RTS Request to Send Input The transceiver does not recognize RTS for flow
control. RTS is used as a control line in RTS/CTS
mode.
8 CTS Clear to Send Output This signal is used to tell the system device connected
to the transceiver that the transceiver is ready to
receive data. When asserted, the transceiver will
accept data, when de-asserted the transceiver does
not accept data. This should always be used for data
rates above 38.4 KB or a risk of lost data may occur if
an RF link is not very robust.
9 GND Ground Signal return for all signal lines shared with Pin 5
98
- Firmware 2.22 1
- Safety Information 2
- Warranty 2
- Restricted Rights 2
- UL Specifications 3
- FCC Notifications 4
- GNU Notification 4
- Document RevisionHistory 5
- LUM0024AB Rev A vi 6
- Table Of Contents 7
- LUM0024AB Rev A xiv 14
- Notational Conventions 15
- Documentation Feedback 16
- Chapter 1: Introduction 17
- Boot-Up LED Sequence 18
- Ethernet Port Conditions 18
- Error LED Conditions 19
- Com Port LED Conditions 19
- Point-to-Point Operation LEDs 20
- LUM0024AB Rev A 6 22
- Chapter 2: Setting Up and 23
- Programming Transceivers 23
- Powering the Transceiver 24
- Using HyperTerminal 25
- Using Discovery Server 30
- ConfigurationTool Options 32
- Navigating the Web Pages 35
- Providing Site Information 36
- Creating User Logins 38
- Adding and Deleting Users 39
- Changing User Passwords 40
- Configuring the TFTP Server 41
- Verifying Firmware Upgrades 44
- LUM0024AB Rev A 30 46
- Chapter 3: IP and Network 47
- Communication Settings 47
- Default Gateway 48
- IP Address 48
- NTP Client Enable 49
- NTP IP Address 49
- Push to Syslog Server 49
- Spanning Tree 49
- Subnet Mask 50
- Syslog Server 1 50
- Syslog Server 2 50
- VLAN Data ID 51
- VLAN Default Gateway 51
- VLAN IP Address 51
- VLAN Management ID 51
- VLAN Mode 52
- VLAN Subnet Mask 52
- Web Page Port (http) 52
- LUM0024AB Rev A 38 54
- Disabling Serial Ports 56
- Ethernet (Rx and Tx) 58
- Serial (Rx and Tx) 58
- Alarm IP & Port 58
- Alarm Retry Limit (Attempts) 59
- Drop Link 59
- Multicast IP 59
- Multicast Port 60
- Serial Baud Rate 60
- Serial CD Mode 60
- Serial Data Bits 61
- Serial Flow Control 61
- Serial Interface 61
- Serial Modbus RTU 61
- Serial Parity 62
- Stop Bits 62
- TCP Client Enable 62
- TCP Client IP 63
- TCP Client Port 63
- TCP Server Enable 63
- TCPServer Inactivity Timeout 63
- TCPServer Port 64
- UDP Local IP Port 64
- UDP Power Up IP 64
- UDP Power Up Port 65
- UDP/Multicast Enable 65
- Utilize For Alarm 66
- Chapter 5: Radio Settings 67
- Addressed Repeat 68
- Broadcast Repeat 68
- Frequency Key 70
- Frequency Zones 70
- Network ID 70
- Master Tx Beacon 71
- Modem Mode 74
- Network Type 75
- Repeaters 76
- Retry Timeout 76
- RF Data Rate 77
- Slave Attempts 77
- Slave Connect Odds 78
- Subnet ID 78
- Subnet ID Example 79
- Transmit Power 81
- Transmit Rate 81
- About the Call Book 82
- LUM0024AB Rev A 70 86
- Chapter 6: Security Settings 87
- Security Parameter Reference 88
- Detach Local Ethernet 89
- Force SSL (https) 89
- MAC Filter 89
- Peer To Peer 90
- RADIUS Enable 90
- RADIUS IP Address 91
- RADIUS Port 91
- Shared Secret 91
- User Password 91
- Chapter 7: SNMP Settings 93
- Auth Method 94
- Auth Password (v3) 94
- Privacy Method 94
- Privacy Password (v3) 95
- Read Community 95
- SNMP Version 95
- Trap Community 95
- Trap Manager IP 96
- Trap Version 96
- Write Community 96
- Delta Alarm Enable 97
- Delta Alarm Below 97
- Min Fault Time 97
- Noise Alarm Above 97
- Noise Alarm Enable 98
- Rx Rate Alarm Below 98
- Rx Rate Alarm Enable 98
- Signal Alarm Below 98
- Signal Alarm Enable 99
- Tx Rate Alarm Below 99
- Tx Rate Alarm Enable 99
- VSWR Alarm Above 99
- VSWR Alarm Enable 100
- Voltage Alarm Above 100
- Voltage Alarm Below 100
- Voltage Alarm Enable 100
- Available Statistics 102
- Upstream Noise 105
- Upstream Signal 105
- Wireless Version 105
- LUM0024AB Rev A 90 106
- LUM0024AB Rev A 94 110
- Information 111
- RS485 Half Duplex Pinouts 112
- RJ45 to DB9 Cable 112
- DB9 Connector Pin Assignments 113
- FGR2-PE Specifications 115
- LUM0024AB Rev A 116
- Specification 116
- Factory Default Settings 117
- Parameter Default Setting 118
- Mechanical Drawing 122
- Appendix A: Firmware Updates 123
- Version 2.21 124
- Version 2.20 124
- LUM0024AB Rev A 110 126
- TFTP Control Options 129
- TFTP Server Log 129
- Clearing the TFTP Server File 130
- LUM0024AB Rev A 120 136
- Address in Windows 137
- TECHNOLOGIES-MIB 141
- LUM0024AB Rev A 126 142
- (continued) 143
- LUM0024AB Rev A 134 150
Související produkty a manuály pro Senzory Baseline-systems FreeWave Ethernet Radio
(3 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce