Baseline-systems FreeWave Ethernet Radio Uživatelský manuál Strana 28
- Strana / 160
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
FGR2-PE Wirelss Data Transceiver
LUM0024AB Rev A
Important: To make changes to the connection properties, you must first disconnect
the terminal session.
To set or determine the transceiver's IP address using HyperTerminal:
1. With the HyperTerminal session from the above procedure open, connect power to the transceiver.
After a few seconds, the following screen display in the HyperTerminal window:
2. Type a Y or a y within 5 seconds (even though the text says 2 seconds) to access the IP setup of
the transceiver.
Any other key exits, allowing the transceiver to complete the boot-up. After entering a Y, a
password prompt displays:
3. Enter the Administrator password (factory default password is admin) to display the Setup menu:
12
- Firmware 2.22 1
- Safety Information 2
- Warranty 2
- Restricted Rights 2
- UL Specifications 3
- FCC Notifications 4
- GNU Notification 4
- Document RevisionHistory 5
- LUM0024AB Rev A vi 6
- Table Of Contents 7
- LUM0024AB Rev A xiv 14
- Notational Conventions 15
- Documentation Feedback 16
- Chapter 1: Introduction 17
- Boot-Up LED Sequence 18
- Ethernet Port Conditions 18
- Error LED Conditions 19
- Com Port LED Conditions 19
- Point-to-Point Operation LEDs 20
- LUM0024AB Rev A 6 22
- Chapter 2: Setting Up and 23
- Programming Transceivers 23
- Powering the Transceiver 24
- Using HyperTerminal 25
- Using Discovery Server 30
- ConfigurationTool Options 32
- Navigating the Web Pages 35
- Providing Site Information 36
- Creating User Logins 38
- Adding and Deleting Users 39
- Changing User Passwords 40
- Configuring the TFTP Server 41
- Verifying Firmware Upgrades 44
- LUM0024AB Rev A 30 46
- Chapter 3: IP and Network 47
- Communication Settings 47
- Default Gateway 48
- IP Address 48
- NTP Client Enable 49
- NTP IP Address 49
- Push to Syslog Server 49
- Spanning Tree 49
- Subnet Mask 50
- Syslog Server 1 50
- Syslog Server 2 50
- VLAN Data ID 51
- VLAN Default Gateway 51
- VLAN IP Address 51
- VLAN Management ID 51
- VLAN Mode 52
- VLAN Subnet Mask 52
- Web Page Port (http) 52
- LUM0024AB Rev A 38 54
- Disabling Serial Ports 56
- Ethernet (Rx and Tx) 58
- Serial (Rx and Tx) 58
- Alarm IP & Port 58
- Alarm Retry Limit (Attempts) 59
- Drop Link 59
- Multicast IP 59
- Multicast Port 60
- Serial Baud Rate 60
- Serial CD Mode 60
- Serial Data Bits 61
- Serial Flow Control 61
- Serial Interface 61
- Serial Modbus RTU 61
- Serial Parity 62
- Stop Bits 62
- TCP Client Enable 62
- TCP Client IP 63
- TCP Client Port 63
- TCP Server Enable 63
- TCPServer Inactivity Timeout 63
- TCPServer Port 64
- UDP Local IP Port 64
- UDP Power Up IP 64
- UDP Power Up Port 65
- UDP/Multicast Enable 65
- Utilize For Alarm 66
- Chapter 5: Radio Settings 67
- Addressed Repeat 68
- Broadcast Repeat 68
- Frequency Key 70
- Frequency Zones 70
- Network ID 70
- Master Tx Beacon 71
- Modem Mode 74
- Network Type 75
- Repeaters 76
- Retry Timeout 76
- RF Data Rate 77
- Slave Attempts 77
- Slave Connect Odds 78
- Subnet ID 78
- Subnet ID Example 79
- Transmit Power 81
- Transmit Rate 81
- About the Call Book 82
- LUM0024AB Rev A 70 86
- Chapter 6: Security Settings 87
- Security Parameter Reference 88
- Detach Local Ethernet 89
- Force SSL (https) 89
- MAC Filter 89
- Peer To Peer 90
- RADIUS Enable 90
- RADIUS IP Address 91
- RADIUS Port 91
- Shared Secret 91
- User Password 91
- Chapter 7: SNMP Settings 93
- Auth Method 94
- Auth Password (v3) 94
- Privacy Method 94
- Privacy Password (v3) 95
- Read Community 95
- SNMP Version 95
- Trap Community 95
- Trap Manager IP 96
- Trap Version 96
- Write Community 96
- Delta Alarm Enable 97
- Delta Alarm Below 97
- Min Fault Time 97
- Noise Alarm Above 97
- Noise Alarm Enable 98
- Rx Rate Alarm Below 98
- Rx Rate Alarm Enable 98
- Signal Alarm Below 98
- Signal Alarm Enable 99
- Tx Rate Alarm Below 99
- Tx Rate Alarm Enable 99
- VSWR Alarm Above 99
- VSWR Alarm Enable 100
- Voltage Alarm Above 100
- Voltage Alarm Below 100
- Voltage Alarm Enable 100
- Available Statistics 102
- Upstream Noise 105
- Upstream Signal 105
- Wireless Version 105
- LUM0024AB Rev A 90 106
- LUM0024AB Rev A 94 110
- Information 111
- RS485 Half Duplex Pinouts 112
- RJ45 to DB9 Cable 112
- DB9 Connector Pin Assignments 113
- FGR2-PE Specifications 115
- LUM0024AB Rev A 116
- Specification 116
- Factory Default Settings 117
- Parameter Default Setting 118
- Mechanical Drawing 122
- Appendix A: Firmware Updates 123
- Version 2.21 124
- Version 2.20 124
- LUM0024AB Rev A 110 126
- TFTP Control Options 129
- TFTP Server Log 129
- Clearing the TFTP Server File 130
- LUM0024AB Rev A 120 136
- Address in Windows 137
- TECHNOLOGIES-MIB 141
- LUM0024AB Rev A 126 142
- (continued) 143
- LUM0024AB Rev A 134 150
Související produkty a manuály pro Senzory Baseline-systems FreeWave Ethernet Radio
(3 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.224 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce